FT44H lever floating ball steam trap valve

FT44H lever floating ball steam trap valve
  • sell:021-32051999
  • sell:021-32050777
  • fax:021-66099555

Details

  • Product Introduction
  • Service Promise
  • Ordering Process

FT44H lever floating ball steam trap valve


Performance advantages


1. Continuous discharge of saturated condensate heating equipment will not have water accumulation, thus achieving the highest thermal efficiency.


2. When the steam pressure changes, the opening of the seat hole of the valve can be adjusted automatically by the floating ball driving lever. The operation is continuous and the performance is stable.


3, exhaust air performance is good. The automatic air exhausting device can discharge non condensing hot and cold gas without air lock, and work smoothly and without noise.


4, excellent sealing performance. The seal adopts spherical seal, and there is no centralized wear life.


purpose


Used in steam heating equipment and condensate recovery system and the working conditions that need to remove condensate quickly, condensate can be automatically, rapidly and continuously removed, effectively prevent steam leakage, and obtain the best heating effect.


Working principle


When the valve is just started, the automatic air exhausting device quickly eliminates the non condensable gas in the system. When steam and hot condensate enter, the temperature in the valve chamber increases, the exhaust air device automatically closes, the float rises and falls according to the change of condensate water level, drives the lever to adjust the opening of the valve seat, and continuously discharges condensate. When the condensate stops entering, the float drops by weight, driving the lever to drive the spool to close the drain valve seat hole.


Use and maintenance


1, we should confirm that the maximum material, pressure and temperature of the valve body can meet the requirements of the working condition.


2, before installation, the pipeline must be cleaned and debris removed.


3, installation position should be as close as possible to heating equipment.


4, should be installed at the lowest point of the pipeline, and the direction of flow is consistent with the direction marked on the valve body.


5, each heating equipment should install traps separately, so as not to affect each other.


6. In order to ensure the safe operation of the system, slowly open the trap money valve to gradually warm up to the normal state.


7, regular maintenance, to ensure the normal work of steam traps.


Selection is the main basis.


Condensate load (drain volume) kg/h (2-3 times the multiplying rate)


Maximum working pressure MPa


Working pressure differential MPa


Valve body material and nominal pressure


Connection mode and size

Main dimensions


型号
公称通径
L
H
H1
S ∅
A×C
16
FT44H 25
40
杠杆浮球式
15
150
153
75
105
95×95
20
150
153
75
105
95×95
25
160
153
75
105
95×95
32
270
240
85
150
147×147
40
270
240
85
150
147×147
50
270
240
85
150
147×147
65
270
240
85
150
210×210
80
350
300
90
210
210×210
100
350
300
90
210
210×210


The best quality, first-class service Qigao creates more value for you!

"Qigao Valve" expects to continuously improve service quality and strive for excellence. "Sincere service" is the eternal theme of "Qigao". "Qigao" strictly followsIS09001-2000 Quality system certification requirements, strict quality control, responsibility to people, to ensure the healthy operation of production, sales and service. Strengthen communication with users and provide quality products to our customers with perfection and perfect service. Hereby our factory makes the following commitments:

Product Standards:

Products in strict accordance with ChinaGB、HG Standard and USAPISuch as standard design, manufacturing, acceptance. The hardness of the sealing surface meets the requirements of the state and the width exceeds the national standard.

pre-sale service:

Product introduction, technical exchange, non-standard product design, troubleshooting。

Sale service:

A trustworthy contract guarantees timely delivery and keeps in touch with customers. For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.

After sales service:

1、"Qigao" brand product quality period is from the factory12In the month, the implementation of the "three guarantees" service (return, replacement, warranty).

2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions, so as to further improve product quality.

3、Respond quickly to the quality of user complaints, after-sales service personnel rushed to the scene in 24-36 hours (48 hours outside the province).

4、For after-sales service, users are required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of Qigao.

1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:

a、Structure length;

b、Connection Type;

c、Nominal diameter, full diameter, reduced diameter, pipe size;

d、Operating medium and temperature, pressure range;

e、Tests, inspection standards and other requirements

2、The factory can configure various types of driving devices according to customer's specific requirements.。

3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.

4、For futures and order customers, please call us in advance to tell the required valve model, specification, quantity, delivery time and location, and timely transfer to the factory account according to the total 30% deposit or full payment. The rest of the payment is pending. Import before shipment to arrange delivery in time.

 

Order Process:

1、Customer purchase list fax to021-33872143,Or call us 021-33872141

2、Receive customer purchase list, provide valve model selection and quotation (price list)。

3、Specific agreement: delivery date, special requirements, etc.。

download Google:

1、If the customer has special requirements for the product, the following instructions must be provided in the order contract.:

a、Structure length;

b、Connection Type;

c、Nominal diameter, full diameter, reduced diameter, pipe size;

d、Operating medium and temperature, pressure range;

e、Tests, inspection standards and other requirements

2、The factory can configure various types of driving devices according to customer's specific requirements.。

3、If the type and model of the valve are determined by the customer, the customer shall correctly state the meaning and requirements of the model and sign the contract under the condition that the supplier and the buyer understand each other.

4、For futures and order customers, please call us first to tell the required valve model, specifications, quantity, delivery time and location, and press the total30%The deposit or full payment will be remitted to our factory account in time., The rest of the payment will be remitted before shipment to arrange delivery in time.。

Sale service:

Trustworthy contract, guarantee timely delivery, keep in touch with customers at any time。

For special or duplicate products, our factory arranges technicians to use and troubleshoot the products for users.

After sales service:

1、"Qigao" product quality period is from the factory12Month, practiceThree packsService (return, replacement, warranty)。

2、During the use of our products, our factory regularly organizes technical and quality inspection personnel to visit and consult users for feedback on product quality, usage status and improvement opinions.,
In order to further improve product quality。

3、Respond quickly to the quality of user complaints, after-sales service personnel24-36Hours (outside the province48Hour) rushed to the scene。

4、For after-sales service, the user is required to fill out the quality feedback information form after the service and make an appraisal opinion in order to improve the service quality of “Qigao”.。

statement

  1. All text, data and pictures in this article are for reference only.FT44H lever floating ball steam trap valvePlease contact us at 4000-700-665 for details of performance, size and price.
  2. If there is no explanation, this article is original, reprint, please indicate the address of this article, thank you for your cooperation!